Tri Electronics GT-4000 Gold 6 - 24 karat all Color Alloy Tester

$374.99

Tri Electronics GT-4000 Gold 6 - 24 karat all Color Alloy Tester

The essential tool that goes to high range. Tests gold alloys from 6 to 24 karats in all four colors.

Accurately tests from 6 to 18 and 24 karats values and then range of 20-22 karats.

No dangerous acids or messy harmful chemicals.

Ecologically safe provides a numeric reading on the LCD display that corresponds to the karat table.

Manufacturer’s repair or replacement warranty two years.

Specifications:

Size: 12” x 9” x 2” (305 x 254 x 76mm)
Weight: 2.0 lb (.900 kg)
P
ower: 2 - 9volt batteries

Low Karatage Testing (6 - 18 karat)

Remove stationary/rotary cap from sensor nozzle by turning the lower LIGHTCOLORED barrel counter clockwise.

Remove the polyethylene cap on the gel cartridge and fully insert the rectangular feed-screw end into the appropriate slot of the rotary cap. Reassemble the cap assembled and cartridge into the sensor body. (See diagram 1)

GT4000 Diagram 1 instructions

Turn the light-colored barrel clockwise until fully seated.

Turn the dark-colored barrel counter clockwise until the first drop of gel appears at the sensor nozzle.

Connect the black wire to the sensor plug outlet, the black and red wire connector to the display unit, and red wire to the testing plate.

Turn the unit "ON". It will automatically be set to low karatage. If Hi Karatage Testing is desired, press the "HI/LOW KARAT"

switch to illuminate the "HI KARAT ON" light and refer to the Hi Karatage Testing section.

Select and clean with eraser a testing point on the object; obtain one drop of gel by turning the sensor rotary cap (dark colored barrel) counter-clockwise until gel is dispersed from sensor end. Firmly press the sensor nozzle to the pre-selected and cleaned testing point and press the "TEST" button.

NOTE: use only a small amount of gel to test. (See diagram 2).

GT-4000 Diagram 2 instructions

It is only necessary to wet gold surface at sensor tip.

After the test, there should be a small round wet spot on the tested sample.

Maintain sensor in the same vertical position for approximately 4-5 seconds while the instrument indicates the numbers of the LCD display. The first test after turning the unit "ON" may give an inaccurate result and should be ignored. Repeat the operation numbers 7 and 8. Then refer to the Karat Table to convert the displayed number into karat value.

Hi Karatage Testing (18-24 karat)

If you sample in the low karatage test shows 18K or more,

1. Activate the Hi Karatage mode by pressing the "Hi/Low Karat" button. The first test in the high karate mode is a pre-test and may give erroneous results - ALWAYS test high karatage gold a second time to determine karatage.

2. Follow all instructions 1) through 8) above to test high karatage gold except use "Hi Karatage On" mode for all testing.

3. Be sure that a high karat gold sample is carefully cleaned at the test point and at the alligator clip contact on both sides of testing sample. To return the GT-4000TM to the low karatage mode, push the "Hi Karat" button again.

If tested gold piece shows "Not Gold", check all connections of wires in unit, plate, and sensor. Also check for the proper amount of gel and round wet spot on the tested item.

This Item can not be returned for a refund. All sales are final.


Add to Cart:

  • Model: GT-4000
  • Shipping Weight: 3lbs
  • 2 Units in Stock
  • Manufactured by: TRI Electronics

This product was added to our catalog on Thursday 20 August, 2009.

Copyright © 2017 GoldTestSolutions.com. Powered by Zen Cart